package/comgt/files/3g.sh

   1 set_3g_led() {
   2         grep WRT54G3G /proc/diag/model >/dev/null || return 0
   3         echo "$1" > /proc/diag/led/3g_green
   4         echo "$2" > /proc/diag/led/3g_blue
   5         echo "$3" > /proc/diag/led/3g_blink
   6 }
   7
   8 scan_3g() {
   9         local device
  10
  11         scan_ppp "$@"
  12         config_get device "$1" device
  13
  14         # try to figure out the device if it's invalid
  15         [ -n "$device" -a -e "$device" ] || {
  16                 for device in /dev/tts/2 /dev/usb/tts/0 /dev/noz0; do
  17                         [ -e "$device" ] && {
  18                                 config_set "$1" device "$device"
  19                                 break
  20                         }
  21                 done
  22         }
  23
  24         # enable 3G with the 3G button by default
  25         config_get button "$1" button
  26         [ -z "$button" ] && {
  27                 config_set "$1" button 1
  28         }
  29 }
  30
  31 stop_interface_3g() {
  32         set_3g_led 0 0 0
  33         killall gcom >/dev/null 2>/dev/null
  34 }
  35
  36 setup_interface_3g() {
  37         local iface="$1"
  38         local config="$2"
  39
  40         config_get device "$config" device
  41
  42         for module in slhc ppp_generic ppp_async; do
  43                 /sbin/insmod $module 2>&- >&-
  44         done
  45
  46         config_get apn "$cfg" apn
  47         config_get service "$cfg" service
  48         config_get pincode "$cfg" pincode
  49         config_get mtu "$cfg" mtu
  50
  51         set_3g_led 1 0 1
  52
  53         # figure out hardware specific commands for the card
  54         if gcom -d "$device" -s /etc/gcom/getcardinfo.gcom | grep Novatel 2>/dev/null >/dev/null; then
  55                 case "$service" in
  56                         umts_only) CODE=2;;
  57                         gprs_only) CODE=1;;
  58                         *) CODE=0;;
  59                 esac
  60                 mode="AT\$NWRAT=${CODE},2"
  61         else
  62                 case "$service" in
  63                         umts_only) CODE=1;;
  64                         gprs_only) CODE=0;;
  65                         *) CODE=3;;
  66                 esac
  67                 mode="AT_OPSYS=${CODE}"
  68         fi
  69
  70         PINCODE="$pincode" gcom -d "$device" -s /etc/gcom/setpin.gcom || {
  71                 echo "$cfg(3g): Failed to set the PIN code."
  72                 set_3g_led 0 0 0
  73                 return 1
  74         }
  75         MODE="$mode" gcom -d "$device" -s /etc/gcom/setmode.gcom
  76         set_3g_led 1 0 0
  77
  78         start_pppd "$config" \
  79                 noaccomp \
  80                 nopcomp \
  81                 novj \
  82                 nobsdcomp \
  83                 noauth \
  84                 lock \
  85                 crtscts \
  86                 connect "USE_APN=\"$apn\" /etc/ppp/3g.connect" \
  87                 ${mtu:+mtu $mtu mru $mtu} \
  88                 460800 "$device"
  89 }