comment "Atheros 802.11(a/b/g) PCI/Cardbus support"

config ATHEROS
	tristate "Atheros PCI/Cardbus cards"
	depends on PCI && (NET_RADIO || WIRELESS_EXT) && CRYPTO
       ---help---
	  Say Y here if you intend to attach an Atheros Cardbus or PCI
	  wireless Ethernet networking card to your computer.  This
	  driver support the standard Linux Wireless Extensions.

	  You will also very likely also need the Wireless Tools in order to
	  configure your card and that /etc/pcmcia/wireless.opts works:
	  <http://www.hpl.hp.com/personal/Jean_Tourrilhes/Linux/Tools.html>.

	  To compile this driver as a module, choose M here: the module will be
	  called ath_pci.  If unsure, say N.

config ATHEROS_DEBUG
	bool "Atheros: Debugging support for Atheros PCI/Cardbus cards"
	depends on ATHEROS
	default y
	help
	  Enable diagnostic checks and log output.

choice
	prompt "Atheros: Default Transmission Rate Control Algorithm"
	depends on ATHEROS
	default ATHEROS_RATE_DEFAULT_SAMPLE
	help
	  Select the rate control algorithm to be used by default.  You
	  can select additional algorithms below.

	config ATHEROS_RATE_DEFAULT_AMRR
		bool "AMRR"
		select ATHEROS_RATE_AMRR

	config ATHEROS_RATE_DEFAULT_ONOE
		bool "Onoe"
		select ATHEROS_RATE_ONOE

	config ATHEROS_RATE_DEFAULT_SAMPLE
		bool "Sample"
		select ATHEROS_RATE_SAMPLE

        config ATHEROS_RATE_DEFAULT_MINSTREL
                bool "Minstrel"
                select ATHEROS_RATE_MINSTREL

endchoice

config ATHEROS_RATE_DEFAULT
	string
	default "amrr" if ATHEROS_RATE_DEFAULT_AMRR
	default "onoe" if ATHEROS_RATE_DEFAULT_ONOE
	default "sample" if ATHEROS_RATE_DEFAULT_SAMPLE
        default "minstrel" if ATHEROS_RATE_DEFAULT_MINSTREL

config ATHEROS_RATE_AMRR
	bool "Adaptive Multi-Rate Retry control algorithm"
	depends on ATHEROS
	default y
	help
	  Enable Adaptive Multi-Rate Retry control algorithm.

config ATHEROS_RATE_ONOE
	bool "Atsushi Onoe's rate control algorithm"
	depends on ATHEROS
	default y
	help
	  Enable Atsushi Onoe's rate control algorithm.

config ATHEROS_RATE_SAMPLE
	bool "Sample Rate control algorithm"
	depends on ATHEROS
	default y
	help
	  SampleRate chooses the bitrate it predicts will provide the
	  most throughput based on estimates of the expected per-packet
	  transmission time for each bitrate. SampleRate periodically
	  sends packets at bitrates other than the current one to
	  estimate when another bitrate will provide better performance.
	  SampleRate switches to another bitrate when its estimated
	  per-packet transmission time becomes smaller than the current
	  bitrate's. SampleRate reduces the number of bitrates it must
	  sample by eliminating those that could not perform better than
	  the one currently being used. SampleRate also stops probing at
	  a bitrate if it experiences several successive losses.


config ATHEROS_RATE_MINSTREL
        bool "A wandering minstrel rate control algorithm"
        depends on ATHEROS
        default y
        help
          Similar to the SampleRate code base, except that it is
          a)more carefully written
          b)shown to give a throughput similar to what can be obtained by
            manually fixing either end to fixed rates
          c)verified by monitoring the network traffic with an ieee80211
             enabled ethereal
          d)responds to network changes and does modify the rate accordingly. 
            Thus, on moving the two nodes together/apart, the ideal rate will 
            be changed as appropriate.