--- a/nl80211.h +++ b/nl80211.h @@ -295,7 +295,9 @@ * auth and assoc steps. For this, you need to specify the SSID in a * %NL80211_ATTR_SSID attribute, and can optionally specify the association * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC, - * %NL80211_ATTR_WIPHY_FREQ and %NL80211_ATTR_CONTROL_PORT. + * %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT, + * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and + * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT. * It is also sent as an event, with the BSSID and response IEs when the * connection is established or failed to be established. This can be * determined by the STATUS_CODE attribute. @@ -313,8 +315,8 @@ * channel for the specified amount of time. This can be used to do * off-channel operations like transmit a Public Action frame and wait for * a response while being associated to an AP on another channel. - * %NL80211_ATTR_WIPHY or %NL80211_ATTR_IFINDEX is used to specify which - * radio is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the + * %NL80211_ATTR_IFINDEX is used to specify which interface (and thus + * radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the * frequency for the operation and %NL80211_ATTR_WIPHY_CHANNEL_TYPE may be * optionally used to specify additional channel parameters. * %NL80211_ATTR_DURATION is used to specify the duration in milliseconds @@ -385,6 +387,8 @@ * of any other interfaces, and other interfaces will again take * precedence when they are used. * + * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -487,6 +491,7 @@ enum nl80211_commands { NL80211_CMD_NOTIFY_CQM, NL80211_CMD_SET_CHANNEL, + NL80211_CMD_SET_WDS_PEER, /* add new commands above here */ @@ -686,6 +691,15 @@ enum nl80211_commands { * request, the driver will assume that the port is unauthorized until * authorized by user space. Otherwise, port is marked authorized by * default in station mode. + * @NL80211_ATTR_CONTROL_PORT_ETHERTYPE: A 16-bit value indicating the + * ethertype that will be used for key negotiation. It can be + * specified with the associate and connect commands. If it is not + * specified, the value defaults to 0x888E (PAE, 802.1X). This + * attribute is also used as a flag in the wiphy information to + * indicate that protocols other than PAE are supported. + * @NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT: When included along with + * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, indicates that the custom + * ethertype frames used for key negotiation must not be encrypted. * * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver. * We recommend using nested, driver-specific attributes within this. @@ -787,6 +801,33 @@ enum nl80211_commands { * This is used in association with @NL80211_ATTR_WIPHY_TX_POWER_SETTING * for non-automatic settings. * + * @NL80211_ATTR_SUPPORT_IBSS_RSN: The device supports IBSS RSN, which mostly + * means support for per-station GTKs. + * + * @NL80211_ATTR_WIPHY_ANTENNA_TX: Bitmap of allowed antennas for transmitting. + * This can be used to mask out antennas which are not attached or should + * not be used for transmitting. If an antenna is not selected in this + * bitmap the hardware is not allowed to transmit on this antenna. + * + * Each bit represents one antenna, starting with antenna 1 at the first + * bit. Depending on which antennas are selected in the bitmap, 802.11n + * drivers can derive which chainmasks to use (if all antennas belonging to + * a particular chain are disabled this chain should be disabled) and if + * a chain has diversity antennas wether diversity should be used or not. + * HT capabilities (STBC, TX Beamforming, Antenna selection) can be + * derived from the available chains after applying the antenna mask. + * Non-802.11n drivers can derive wether to use diversity or not. + * Drivers may reject configurations or RX/TX mask combinations they cannot + * support by returning -EINVAL. + * + * @NL80211_ATTR_WIPHY_ANTENNA_RX: Bitmap of allowed antennas for receiving. + * This can be used to mask out antennas which are not attached or should + * not be used for receiving. If an antenna is not selected in this bitmap + * the hardware should not be configured to receive on this antenna. + * For a more detailed descripton see @NL80211_ATTR_WIPHY_ANTENNA_TX. + * + * @NL80211_ATTR_MCAST_RATE: Multicast tx rate (in 100 kbps) for IBSS + * * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use */ @@ -951,6 +992,16 @@ enum nl80211_attrs { NL80211_ATTR_RX_FRAME_TYPES, NL80211_ATTR_FRAME_TYPE, + NL80211_ATTR_CONTROL_PORT_ETHERTYPE, + NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT, + + NL80211_ATTR_SUPPORT_IBSS_RSN, + + NL80211_ATTR_WIPHY_ANTENNA_TX, + NL80211_ATTR_WIPHY_ANTENNA_RX, + + NL80211_ATTR_MCAST_RATE, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -1006,6 +1057,8 @@ enum nl80211_attrs { * @NL80211_IFTYPE_WDS: wireless distribution interface * @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames * @NL80211_IFTYPE_MESH_POINT: mesh point + * @NL80211_IFTYPE_P2P_CLIENT: P2P client + * @NL80211_IFTYPE_P2P_GO: P2P group owner * @NL80211_IFTYPE_MAX: highest interface type number currently defined * @NUM_NL80211_IFTYPES: number of defined interface types * @@ -1022,6 +1075,8 @@ enum nl80211_iftype { NL80211_IFTYPE_WDS, NL80211_IFTYPE_MONITOR, NL80211_IFTYPE_MESH_POINT, + NL80211_IFTYPE_P2P_CLIENT, + NL80211_IFTYPE_P2P_GO, /* keep last */ NUM_NL80211_IFTYPES, @@ -1111,6 +1166,8 @@ enum nl80211_rate_info { * @NL80211_STA_INFO_RX_PACKETS: total received packet (u32, from this station) * @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (u32, to this * station) + * @NL80211_STA_INFO_TX_RETRIES: total retries (u32, to this station) + * @NL80211_STA_INFO_TX_FAILED: total failed packets (u32, to this station) */ enum nl80211_sta_info { __NL80211_STA_INFO_INVALID, @@ -1124,6 +1181,8 @@ enum nl80211_sta_info { NL80211_STA_INFO_TX_BITRATE, NL80211_STA_INFO_RX_PACKETS, NL80211_STA_INFO_TX_PACKETS, + NL80211_STA_INFO_TX_RETRIES, + NL80211_STA_INFO_TX_FAILED, /* keep last */ __NL80211_STA_INFO_AFTER_LAST, @@ -1277,7 +1336,11 @@ enum nl80211_bitrate_attr { * wireless core it thinks its knows the regulatory domain we should be in. * @NL80211_REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an * 802.11 country information element with regulatory information it - * thinks we should consider. + * thinks we should consider. cfg80211 only processes the country + * code from the IE, and relies on the regulatory domain information + * structure pased by userspace (CRDA) from our wireless-regdb. + * If a channel is enabled but the country code indicates it should + * be disabled we disable the channel and re-enable it upon disassociation. */ enum nl80211_reg_initiator { NL80211_REGDOM_SET_BY_CORE, @@ -1382,6 +1445,17 @@ enum nl80211_reg_rule_flags { * @__NL80211_SURVEY_INFO_INVALID: attribute number 0 is reserved * @NL80211_SURVEY_INFO_FREQUENCY: center frequency of channel * @NL80211_SURVEY_INFO_NOISE: noise level of channel (u8, dBm) + * @NL80211_SURVEY_INFO_IN_USE: channel is currently being used + * @NL80211_SURVEY_INFO_CHANNEL_TIME: amount of time (in ms) that the radio + * spent on this channel + * @NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY: amount of the time the primary + * channel was sensed busy (either due to activity or energy detect) + * @NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY: amount of time the extension + * channel was sensed busy + * @NL80211_SURVEY_INFO_CHANNEL_TIME_RX: amount of time the radio spent + * receiving data + * @NL80211_SURVEY_INFO_CHANNEL_TIME_TX: amount of time the radio spent + * transmitting data * @NL80211_SURVEY_INFO_MAX: highest survey info attribute number * currently defined * @__NL80211_SURVEY_INFO_AFTER_LAST: internal use @@ -1390,6 +1464,12 @@ enum nl80211_survey_info { __NL80211_SURVEY_INFO_INVALID, NL80211_SURVEY_INFO_FREQUENCY, NL80211_SURVEY_INFO_NOISE, + NL80211_SURVEY_INFO_IN_USE, + NL80211_SURVEY_INFO_CHANNEL_TIME, + NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY, + NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY, + NL80211_SURVEY_INFO_CHANNEL_TIME_RX, + NL80211_SURVEY_INFO_CHANNEL_TIME_TX, /* keep last */ __NL80211_SURVEY_INFO_AFTER_LAST, @@ -1636,11 +1716,14 @@ enum nl80211_auth_type { * @NL80211_KEYTYPE_GROUP: Group (broadcast/multicast) key * @NL80211_KEYTYPE_PAIRWISE: Pairwise (unicast/individual) key * @NL80211_KEYTYPE_PEERKEY: PeerKey (DLS) + * @NUM_NL80211_KEYTYPES: number of defined key types */ enum nl80211_key_type { NL80211_KEYTYPE_GROUP, NL80211_KEYTYPE_PAIRWISE, NL80211_KEYTYPE_PEERKEY, + + NUM_NL80211_KEYTYPES }; /** @@ -1671,6 +1754,9 @@ enum nl80211_wpa_versions { * CCMP keys, each six bytes in little endian * @NL80211_KEY_DEFAULT: flag indicating default key * @NL80211_KEY_DEFAULT_MGMT: flag indicating default management key + * @NL80211_KEY_TYPE: the key type from enum nl80211_key_type, if not + * specified the default depends on whether a MAC address was + * given with the command using the key or not (u32) * @__NL80211_KEY_AFTER_LAST: internal * @NL80211_KEY_MAX: highest key attribute */ @@ -1682,6 +1768,7 @@ enum nl80211_key_attributes { NL80211_KEY_SEQ, NL80211_KEY_DEFAULT, NL80211_KEY_DEFAULT_MGMT, + NL80211_KEY_TYPE, /* keep last */ __NL80211_KEY_AFTER_LAST,